Better results with a newfound inclusion.
Why Trial Runs Using Magic-Glos Resin?
Lisa Pavelka’s Magic-Glos UV Resin allows me to work fast (layers cure in 15 minutes), build a focal bead in layers, and experiment. I’m using this resin to try out some new products, techniques, combinations, and sequences as I learn my preferences in resin faux opal making.
Sure, it’s more expensive per ounce, but ruining a whole batch or three of a dozen or more beads at a time is even more disheartening. If I didn’t allow for a leaning curve like this first, I probably would have given up on resin. It can take months or years to really master the medium. (Things seem ridiculously easy in the mind’s eye if our imagination isn’t informed by experience and tried and trusted knowledge base, I’ve found.)
So, here are some of my best results so far, note the slight amber tone at this depth with this resin, and I’m about to Faux Opals in Ice Resin and ArtResin. (See How to Ice Resin, How to ArtResin.) At this thickness, I expect almost no amber tone with Ice Resin and no detectable amber tone with ArtResin.
Magic-Glos Resin Tips
1. Don’t seal paper or cardstock inclusions with Mod Podge or PVC (white craft) glues if you’re using them with Magic-Glos — reactions between water-activated mediums, inks, and Magic-Glos can occur over time.
2. Bubbles can be prevented almost all the time. Read resouces given here. Bubbles can be removed by letting cured item sit one hour, drilling a hole into the bubble, cleaning up drilling debris, adding just enough Magic-Glos, and curing again.
Things Magic-Glos Doesn’t Work Well With
- PVC glues – your white craft, nearly all decoupage mediums/glues, and school glues are PVC glues — https://thebluebottletree.com/what-is-the-difference-between-mod-podge-and-acrylic-medium
- Air–dry glues — air-dry glues get trapped under things, don’t cure 100%, then release air bubbles into your curing resin. Use two-part epoxy glue instead!
- Ice Resin, whether or not each resin is cured or wet (insured) — chemical reaction between the two resins causes cloudiness
- Water-based sealants – any sealants that are not waterproof after drying (water resistant is not waterproof)
- Alcohol inks
- Unsealed inkjet prints
- Anything that may run or bleed if wet
- Sharpie markers
If in doubt, test first, often weeks ahead to make doubly sure.
Don’t. Don’t bake Magic-Glos. Avoid temperatures over 100 degrees F. See MSDS.
Warning: Baking Magic-Glos with polymer clay will cause the resin to amber (brown). See MSDS sheet (link given above) for further info.
Doming, Pulling Away, and Self-Leveling Properties and What They Mean to the User — The same properties that allow Magic-Glos to dome causes the resin to pull away from edges/periphery in first layer or two, hence a good dome is built up in layers, each of which are cured before the next is added. The last layers are minimal amounts and it may help to spread the resin nearly to the edge (with a toothpick or small ballpoint stylus) and then let Magic-Glos self-leveling finish the job, finally fully covering evenly and doming. Let it sit 10 minutes to 1/2 hour out of UV light to let it finish self-leveling and to let air bubbles make themselves evident. The self-leveling properties mean that you might think you only added enough, the self-doming is a bit of a delayed reaction, and then suddenly you have Magic-Glos running over the sides. If still uncured, it can be cleaned up with cotton swabs and wet wipes but prevention is better than damage control. Prevention involves adding thinner, multiple layers that are each cured before the next is added and curing your item while on a pedestal — a bit of polymer clay or poster-tx on a craft mirror a bit larger than your piece but small enough to fit in the UV lamp oven.
If the overfill cured, it can be pried off with your hands and/or chipped off with a craft knife.
Minimum Number Of Layers — usually 2 layers, less is more, meaning it’s better to add thin/incomplete layers than to overfill. Thinner layers allows the air bubble popping method of passing a butane mini torch or windproof lighter over the surface of the Magic-Glos for one and only one second.