Raised Scratch Foam Designs in Polymer Clay

Raised Scratch Foam Polymer Clay Designs

Raised Scratch Foam Designs in Polymer Clay

Raised Scratch Foam Polymer Clay Design Test, with notes, by Karen A. Scofield

KarenAScofield Spriograph Clay Texture SheetsNote: This page will be updated as examples are made.

The above picture is only a simple and fast test. It’s not meant to be a prime example, just an example to get your creative juices flowing (and mine). It shows a moon shaped piece of clay with a raised scratch foam design that was colored with Pearl Ex.

I haven’t yet seen others doing it, but yes indeedy, spirographs can be used on scratch foam (Inovart Presto Foam Printing Plate was used in this case) with a ball point pen, ball stylus, or Sakura Gel Pen.

Back at it, Dec. 2016.

KarenAScofield Spriograph Clay Texture Sheets

spirograph clay texture sheet by Karen a Scofield

The Basic Idea

Create a design on scratch foam with a spirograph set and a ball point pen. Press  polymer clay into the design and lift. Add bead holes, etc. You’re looking for spirograph sets that won’t make unintended scratches on the scratch foam. Mine came with “The Spiral Draw” Book.

Taking it Further

Pointillism elements or entire designs be be added inside or around the spirograph design with a ball point pen or ball stylus. The result creates raised clay designs once clay is preseed into it.

Ball point styluses that come in varying sizes can be used for added interest and then needles or beed hole makers can be dragged across the surface, at a slant, to add on to the design too.

Scratch foam designs are probably more commonly used for printing monoprints and other techniques … and also by metal clay artists. They can be earthy/rustic looking or linear and crisp ones.

One can create a bezel complete with boarder designs, with scratch foam designs. What you indent on the foam will be raised on the clay. If you add dimensional writer designs to the scratch foam ones, the clay pressed into it will have both raised and indented designs.

If you use Sakura Gel Pens for the spirograph scratch foam deisgns, many of their inks are oqaque and therefore show up on darker clays. You can press the clay into the fresh scratch foam design and then bake. You may want to seal your design afterward.

Any manner of polymer clay extrusions, applique, relief sculpture, lace impressions/molds, designs for faux enamels, crackling, or designs made with cutters/blades can be applied over the spirograph textured clay passages. If you’re worried about pressing clay together to cause adhesion, because you don’t want to ruin more delicate designs, you may want to use liquid clay or Bake and Bond for adhesion purposes.

With single layer or multi layered scratch foam designs, you create mixed media mosaic tiles, embellishments, beads, and larger clay sheets. You can create molds of the larger clay sheets if you want.

Raised designs can be colored with paint, Sakura Gel Pen ink, inks, or Pearl Ex powders (which are a brand of mica powder). I’d apply paint to baked clay but Sakura Gel Pen, Pearl Ex, and alcohol inks can be applied to raw clay that’s then baked.

You may want to seal baked polymer clay items that have Pearl Ex mica powders or Gel Pens baked onto them. Varathane Water Based varnish is a wonderful sealant for polymer clay pieces.

Advertisements

5 thoughts on “Raised Scratch Foam Polymer Clay Designs

    • Cool! Me, I got stuck on faux rock experiments and in how to transfer scratch foam designs to more permanent polymer clay texture sheets. Also, people using scratch foam for prints described it as nonstick. Scratch foam, however, can actually fuse to the polymer clay (or at least it did with my UltraLight Sculpey-Classic Fimo mix). Other issues I’ve found are that you might have to go over the lines again if you use it more than once, it probably can be used only a few times, it should be cleaned with rubbing alcohol wipes after each contact with polymer clay, and it should be considered temporary even with the best of care anyway. I got really excellent texture though, and that makes it all worth it.

      Like

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s